Why an L1 bid still fails.
Then I'll lay it out with a flow diagram and a chart.


Being L1 only means you quoted the lowest price.
After that, the buyer can still disqualify you, change how the order is split, cancel the bid, or put the order at risk if you miss a deadline. The diagram above shows the four stages, and the bar chart shows one of the price rules in numbers.
1. Technical checks (the biggest reason)
The lowest price only wins among bids that clear technical evaluation first, and a technically non-compliant L1 bid can be rejected so the next qualifying bidder becomes L1. In single-packet bidding, GeM also lets the buyer pick L1 bidders for technical evaluation (per a GeM overview deck). As I read it, that is how you can be L1 on price and still be rejected afterwards.
What usually fails:
- Documents: Losses on technical grounds are almost always an expired or mismatched document, not a missing one. Typical examples are OEM authorisation, ISO, Udyam, turnover and experience proof.
- Specs: The offered product's specification must match the Golden Parameters the buyer chose. Writing "as per datasheet" instead of the exact value the compliance grid asks for can fail you even if the product is fine.
- Missing uploads: Bid documents state that an offer can be rejected if any certificate or document sought in the bid, the ATC (Additional Terms & Conditions) or a corrigendum is not uploaded. A local-content declaration is one example.
- Corrigendum not acknowledged: One seller guide lists this as a common cause of rejection before evaluation.
- Suspension: If the seller is suspended at the time of technical bid opening, the system marks the bidder as disqualified. The FAQ also says such a bidder cannot challenge that rejection.
- Clarification window: Bid documents typically give about 2 days for technical clarifications. Missing that reply can cost you the bid.
2. Price-stage decisions by the buyer
- Negotiation: Buyers can negotiate online with the L1 bidder, with a 72-hour response window and a maximum of five attempts, if approval from the competent authority is in place. Reply inside the window.
- Reverse auction: The buyer can go to an RA if not satisfied with the L1 price.
- Unreasonable price: GeM's incident policy lists "unreasonable offer price" as a deviation reason, and seller guides report that unrealistic quotes get disqualified. Do not quote below your real cost.
- Total or BOQ evaluation: In BOQ bids, the lowest total decides L1, so a single wrong rate has a high impact.
3. Preference rules (MSE and Make in India)
- The buyer can choose MSE preference within L1 + 15% and Make in India preference within L1 + 20%.
- If L1 is not an MSE, a qualifying MSE can be invited to match your price. The buyer can split the order among up to 5 MSE sellers. In some tenders the full quantity goes to the matching MSE, so a non-MSE L1 can end up with a smaller share or none.
- The chart shows an illustrative case: L1 is ₹10 lakh, and an MSE quoting ₹11.2 lakh is inside the ₹11.5 lakh limit.
4. The buyer cancels or retenders
Buyers can cancel or re-tender for documented reasons: specifications needing revision, all bids above estimate, too few qualified bidders, or policy changes. You can do everything right and still get no order.
5. After the award
- Security deadline: ePBG is typically 5% of order value, and sometimes 10%. Failing to furnish it in time is a recorded incident reason.
- Do not withdraw or modify: Withdrawing or modifying a bid within its validity period is also an incident reason.
- Non-delivery: Not delivering after a successful bid can lead to incidents and, with repeated cancellations, a higher severity.
What I could not verify
GeM publishes no official statistics on rejection reasons. Private blogs give conflicting figures (about 35% to 40% of bids failing at the technical stage), so I did not chart them. One guide mentions a 48-hour representation window after technical evaluation. I could not find that on an official GeM page. GeM has also said it does not examine seller representations against buyers' decisions, so disputes go to the buyer. Check the bid document and ATC of each bid, because rules differ by tender.
Quick checklist before you quote
- Check every certificate's expiry date, and make sure each one matches the bid line item.
- Compare your datasheet to the specification line by line and use the exact values.
- Read the ATC and corrigenda.
- Set a price floor and quote above your real cost.
- Keep your DSC, account status and notifications active, and check the bid daily until it is awarded.
- Arrange the ePBG with your bank before you bid.
Comments
Post a Comment